cutport.blogg.se - Cplot prep instructions

#Cplot prep instructions full

The “jug” is mixed with one gallon of water (4 liters). Apply a quality automotive wax after 1 week.Colyte is a bowel cleansing product used to cleanse the bowel prior to colonoscopy. Note: High speed buffers are more aggressive and can damage the paint if used incorrectly. Follow up with a foam pad with a finishing compound. Buff with a random orbital or high speed buffer using a wool buffing pad and fine grit buffing compound. Wash surface with clean water and let dry. Once wet sanding is complete the surface will appear dull. Note: If clear coat is sanded through to the color coat, repeat color and clear coat applications. Lightly wet sand any imperfections or orange peel with 1500-2000 grit sandpaper, being careful not to cut through the clear coat and into the color coat. Test an inconspicuous area to determine if paint has completely dried. After all paint steps are complete let paint dry for 24-48 hours depending on products used.

Apply 1-2 LIGHT COATS of CP199 Adhesion Promoterĭupli-Color® Paints can be wet sanded and buffed to a smooth glossy finish.

Apply appropriate primer per project requirements.

Degrease again with PW100 Prep Wipe or PS100 Prep Spray.

Scuff with RED Scuff pad or 600 grit paper to break any glossy surfaces.Apply 3- 4 good coats of clear (allow 24 hours if wet sanding and buffing).

#Cplot prep instructions full

Apply 2- 3 coats of color or until full coverage is achieved.

Wet sand with 1000 grit with a pliable sanding block and repeat were needed.

Apply 2- 3 coats of FP101 Filler Primer and let dry for 24 hours.

Sand filler with 600 grit paper and repeat where needed.

Apply body filler per manufacturers instructions.

Apply 3-4 good coats of clear (allow 24 hours if wet sanding and buffing).

Apply 2-3 coats of color or until full coverage is achieved.

Degrease with PW100 Prep Wipe or PS100 Prep Spray.

Last 1-2 coats should be heavy but NOT too heavy so the paint runsįor best results read all label instructions on the back of the can. Follow up your tack coat with 2-3 medium coats. The first coat isĬalled your “tack coat” and will help each additional coat bond to

Always start your paint project with light coats.

Surface and spray in an even sweeping motion.

Be sure to shake the aerosol can for 1 full minute prior to painting.Īlways test the aerosol can on a test surface or piece of cardboardīefore starting your paint project.

Inconspicuous area for paint compatibility.

If you are unsure of the surface you are re-coating test a small.

Lacquer paints do not have a re-coat window.

After this time frame, Enamel must fully cure You only have an allowable time frame in which you can applyĮach coat of paint.

Recoat: Take note of the type of paint you are applying (Lacquer or.

Avoid painting in direct sunlight or in the late evening. Range from 60☏ to 95☏ is ideal and humidity levels less thanĪround 70%. Take note of the temperature and humidity levels.Error may result if you rush through your project. Mask off any surrounding areas to protect from overspray.Īlways use a drop cloth or plastic under the paint project.Surface must also be scuffed if it is glossy. All rust and corrosion must be removed prior to painting.Useĭupli-Color prep products to clean the surface. The surface must be dry and grease, wax and oil free.Prep is the most important part of any paint project.Always make sure you are painting in a well ventilated area.Protection when using paint and chemicals.

For maximum product performance read entire label and directions prior to paint application.Here’s a comprehensive how-to guide for stellar results: